Submit search
Specifications:
701K Includes:
All kit components are available individually
Permits technicians to identify the conductor within a bundle, at a cross-connect point or at the remote end. Can be used on twisted pair wiring (telecom, datacom, etc.), single conductors, coaxial cables, de-energized AC wiring and most other wiring.
Features:
77M
77HP
77HP/6A
77HP/6AC
24" test leads (clips)
Constant/warble tone
Continuity testing
Polarity testing
Talk battery supply
Line 1 modular test lead (RJ-11)
3-color LED (identifies AC ring voltage)
Weather resistant design
Bent nose clips with "bed-of-nails" penetrator
Cloth test leads
Power Requirements
One 9V battery, nominal life, 50 hrs
Transmitter Frequency
900/1100Hz alternating, 900Hz constant nominal
Transmitter Power into 600 ohms
7 dBm
Voltage Protection at 600 ohms in CONT
52 VDC (77HP/6A 60 VDC) (all units provide higher voltage protection in OFF/TONE modes)
High-impact ABS Case
1.25 x 2.25 x 2.5, 24" test leads, 4.5 oz. w/battery
Used in conjunction with any tone generator, this Greenlee Tone Probe Amplifier permits wire and cable identification without having to make direct metallic contact with the conductor.
The 200EP-G has a powerful speaker for noisy environments, recessed on/off button control and high gain for accurate wire identification in congested cable bundles and equipment rooms.
Transmitter and receiver are equipped with female F-type connectors and provide both audible and LED test and tone indications. Optional adapter test leads allow 402K use on distribution cables as well as wire pairs or signal conductors. User defined tone output allows up to four 402T Toner units to be used simultaneously for tracing multiple cable runs.
As a continuity tester, the 402K provides both audible tone and LED display to indicate resistance levels and identifies the presence of AC or DC voltage on the cable under test. The newly-designed 402R receiver provides three methods of signal reception:
The 402K CATV Cable Tone Test Kit consists of one transmitter, one receiver, one male F-to-F connector adapter, one male F-to-alligator clip adapter cable and the rugged 700C Carrying Case (also available separately.)
Battery life
Transmitter, 25+ hrs, receiver, 50+ hrs (nominal)
Tone output
Pulsing, 15 dBm into 75 ohms, alternating, 18 dBm into 75 ohms
Transmitter frequency
75 KHz nominal
Voltage protection
Transmitter, 60V (in OFF position); receiver, 50V
High impact ABS housings
Woven polyester case, 14.4 oz total kit
One 9V battery, nominal life 100 hrs
900/1100 Hz alternating nominal
Transmitter power into 600 ohms
7dBm
Talk battery into 600 ohms
10 VDC
Voltage protection at 600 ohms in RES mode
52 VDC (higher in other modes)
Case
High-impact ABS case
Consisting of the 77M Tone Generator and the 200B Inductive Amplifier, this kit can be used on single conductors, twisted pairs, coaxial cables and de-energized electrical wiring. Both units come housed in a polyester zipper pouch
Power requirements
one 9V battery, nominal life 50 hrs
High impact ABS case
1.25 x 2.25 x 2.5", 24" test leads, 4.5 oz w/battery
Power
One 9V battery, nominal life 50 hrs
Probe tip resistance
Metal 0 ohms, plastic 300 ohms minimum
Input impedance
3.5M ohms
Gain
26 dB
Size
1.125 x 2.125 x 9", 5.5 oz w/battery
Allows you to build your own kit using any tone generator and 200 Series probe.
The 77GX Tone Generator incorporates a host of features including microprocessor controlled circuitry for increased reliability, three selectable tone outputs for multiple line identification, two-line polarity indication for fast outlet checks and selectable power outputs for use on open or shorted pairs. The 200GX Inductive Amplifier features a simple, one-button operation and comfortable, ergonomic design. The adjustable volume control, LED visual signal strength indication, and powerful speaker make the 200GX ideal for noisy environments. To provide a single solution for the professional - Tempo's 711K Professional Tone and Probe Kit combining the 77GX Tone Generator and 200GX Inductive Amplifier in a rugged carrying case.
711K Includes:
77GX Tone Generator
200GX Inductive Amplifier
Rugged, woven polyester 700C Dual Carrying Case
The TEMPO Communications 801K Tone and Probe Kit comprises the 77HP/6A High Power Tone Generator and the 200FP Inductive Amplifier in a rugged woven polyester carrying case. The 801K represents the top-of-the range in wire and cable identification. When first turned on the 200FP is in the normal tone probe mode, detecting and playing most voice frequency signals. With a short press of the control button the probe enters the filtered mode, eliminating the hum and buzz created by light fixtures and power lines.
1.2 x 2.25 x 2.5, 24" test leads, 4.5 oz. w/battery
Latching feature identifies intermittent failures (swingers) and confirms operation of switches at remote locations. In latching mode, the Loop Verifier will catch the alarm condition and continue until the tester is reset.
As a tone generator, this Loop Verifier provides a traditional variable tone that can be applied using the 24" red & black test leads or 6-position modular plug, included. The magnetic, back plate allows convenient mounting directly to control panel cabinets & doors.
Battery life (nominal):
100+ hours tone, 15+ hours audible signal
Tone frequency:
900/1100 Hz alternating, nominal
Tone output:
+3 dBm into 600 ohms
Continuity:
N.O. on <50k ohms, off >80k ohms; N.C. on >120k ohms, off <80k ohms
Latch sensitivity:
Any occurrence >100 microseconds
Case:
Weight:
5.5 oz w/battery
The Greenlee RMT-1 Metal tips provide maximum performance when probing insulated wires or making direct metallic contact.
Tempo RMT-1 - Greenlee RMT-1 - Progressive RMT-1
Like our tone generators, Tempo's inductive amplifiers are recognized as industry standards by field service professionals. Used in conjunction with any of our tone generators, the units permit wire and cable identification without having to make direct metallic contact with the conductor. Powerful receiver gain permits accurate identification in even the most congested cable bundles and equipment rooms. Other features include a powerful, two-inch speaker, which eliminates the need for additional buttsets or headsets, a unique, blended, carbon compound tip that reduces conductivity - minimizing the risk of shorting terminals without sacrificing performance - and a recessed on/off push button control. A spare duckbill tip is included.
The 200B Inductive Amplifier can also be used with the nickel-plated brass probe tips.
1.125 x 2.125 x 9", 5.5 oz w/batt
The 200FP Inductive Amplifier offers the same exceptional qualities as Model 200B, plus an adjustable volume control for more precise identifi-cation when tone signal "bleed" is affecting the identification process, and recessed tabs for buttset or headset connections. In addition, an added LED for visual signal strength indication.
300 ohms minimum
35 decibels
1.25 x 1.375 x 9.75", 4.7 oz w/batt
Like our tone generators, Tempo's inductive amplifiers are recognized as "Industry Standards" by field service professionals. Used in conjunction with any of our tone generators, our inductive amplifiers permit wire and cable identification without having to make direct metallic contact with the conductor. Powerful receiver gain permits accurate identification in even the most congested cable bundles and equipment rooms. Includes one each spare duckbill and metal tip.
The 200GX Inductive Amplifier offers the same exceptional qualities as Model 200EP, including an adjustable volume control for more precise identification when tone signal "bleed" is affecting the identification process, recessed tabs for buttset or headset connections and an LED display for visual signal strength indication - but now has a new, rugged, ergonomically-designed housing!
U.S. PAT. NO. 5,457,441; 5,574,769 and 5,577,099
