Calrad 92-180 IR Distribution System - 5 Port Kit
The Calrad 92-180 is a IR Connecting hub with two 3.5mm Jacks to connect two IR Receivers. Designed to simplify the connection of IR receivers and emitters for IR signal distribution. The 92-180 has the ability to send IR signals to 4 sources using a single emitter or 8 sources if double IR emitters are used. One Port is an IR Blaster. Three colored LED indicators show power status, IR signal and IR confirmation.
Product No Longer Available - See Calrad 92-180A
92-180-A Calrad IR Repeater Kit
Calrad 92-180-A IR Repeater Kit, 6 Port Distribution System
This Calrad IR repeater system extends IR (Infrared) remote control signals from one location to another. The IR receiver is typically located on a TV display and receives IR signals from remote controls up to maximum of 33 ft. and re-transmits them to the 6 Port IR distribution block. The 6 x standard IR emitter ports re-transmits the IR signals to multiple pieces of individual equipment using 3 x dual non-flashing IR emitters. This 92-180A IR distribution block requires a 12Vdc power supply (included) or can work through the optional USB type �B� port on 5Vdc, See Diagram 1A below for typical configuration and hookup. Two Additional IR receiver ports are available for adding two additional IR receivers for multi-room control, Calrad IR Receiver part number, 92-181.
280721 Vanco Super IR Receiver
Vanco 280721 Super IR Receiver
- IR Transmitters- Receivers- and Adapters are compatible with Vanco’s HDMI Matrixes- Splitters- Switchers- and Extenders that are enabled with Super IR technology
- HDMI IR Adapter Allows for IR Control over any Vanco HDMI Cable
- Extends IR Signals more than 100m/328ft
- Supports Dual Band IR
- HDMI IR Adapter is IR or CEC Configurable
280720 Vanco Super IR Transmitter
Vanco 280720 Super IR Transmitter
- IR Transmitters- Receivers- and Adapters are compatible with Vanco’s HDMI Matrixes- Splitters- Switchers- and Extenders that are enabled with Super IR technology
- HDMI IR Adapter Allows for IR Control over any Vanco HDMI Cable
- Extends IR Signals more than 100m/328ft
- Supports Dual Band IR
- HDMI IR Adapter is IR or CEC Configurable
Calrad 92-159 In-Wall Designer Style 3 Port IR Block
The Calrad is ideal for receiver-based multi-room systems, this single-gang Designer style IR connecting block can power up to 9 IR emitters. The 92-159 allows you to connect up to 3 emitters to each of the emitter jacks labeled 1-3. Multiple receivers can also connect to the rear terminal block in a parallel configuration. Includes single gang designer style wall plate and 12Vdc power supply. Works with Calrad and industry standard IR products.
Specifications:
- Dimensions: 4” (L) x 1.75” (W) x 1.5” (D)
- IR Emitter Jacks: 3 x 3.5mm mono jacks
- Power+ Status Jacks: 2.1mm coax jacks
- DC Power Supply: 12Vdc, 300ma
- Weight: 56g
Features:
1. Three output emitter jacks
2. IR Status confirmation L.E.D. indicator
3. External 2.1mm status jack
4. 2.1mm power jack with L.E.D. indicator
5. 4 Position IR receiver terminal block
6. Mounts in a single gang wall plate, designer style insert
Calrad 92-160 IR Distribution System
Calrad 92-160 IR DISTRIBUTION SYSTEM
IR Connecting hub with a wired receiver that terminates to a 3.5mm
stereo plug. A terminal block is also provided to support wired type
receiver connections if needed. Designed to simplify the connection of
IR receivers and emitters for IR signal distribution. The 92-160 has the
ability to send IR signals to 6 sources using a single emitter or 12 or
more sources if double or triple IR emitters are used.Three colored LED
indicators show power status, IR signal and IR confirmation. Comes with
one receiver and one emitter, 12 VDC supply.
Calrad 92-165 IR Receiver Cord, 6 Ft. Long
Calrad Electronics 92-165 IR Receiver 6 ft. cord. LCD/ PLASMA FRIENDLY. Works with Calrad's 92-160 IR Distribution Kit.
Labor saving-problem solving solderless connectors, stop cutting off IR emitter or IR receivers 3.5mm plugs, use Calrad part numbers: 30-489T and 30-295-T solderless connectors for easy in the field cable termination.
Specifications:
- IR Frequency: (34-60Khz)
- Cable Length: 6ft.
- Dimensions: IR Receiver: 1.77” (L) x 0.56” (W) x 0.52" (H)
Calrad 92-169-KIT Compact 2 port IR repeater kit
- Entire IR control system to use with devices inside cabinets or in other rooms
- Delivers IR commands to all devices within your home theater system
- Use up to four emitters with the included connecting blocks
Includes:
Two Port Block
IR Receiver
Single & Dual IR Flashing Emitter
12VDC Power Supply.
Calrad 92-170 IR Infrared Distribution Over Coax | Calrad Electronics
An IR injector and coupler system sends remote control signals to your satellite dish, cable box, or DVD using a standard IR remote, even if the component you wish to control is located in another room. The Calrad RF/IR Injector delivers your IR signals over a single coaxial cable up to 300 feet to the actual component. Attach Calrad's Model: 92-165 receiver using the 3.5mm stereo mini plug to the RF/IR Injector, which attaches to your coax cable between the satellite or cable input and the television you'll be watching. The IR Signal Coax Cable Coupler extracts the IR commands on the other end and delivers them to the satellite dish or other component via a Calrad's Model: 92-152 IR emitter. The IR Coupler/Injector are sold in pairs and the Model: 92-165 IR receiver, Model: 92-152 IR emitters are sold separately, as is a 12-Volt DC Power Supply, which is required to power the RF/IR Injector. There are several ways to use the 92-170 system, using coax only for the IR signal itself or with a CATV service or RF modulated system on the coax cable at the same time.
Specifications:- IR Receive, Transmit Frequency Range: 34 khz - 60 khz
- Maximum Coax Cable Distance: 300 ft.
- IR Injector Size: 1.9" (L) x 1.42" (W) x 0.835" (H)
- IR Injector Connectors: 2 x F81 RF Jacks, 1 x 3.5mm Jack
- IR Coupler Size: 2.2" (L) x 1.4" (W) x 1.0" (H)
- IR Coupler Connectors: 2 x F81 RF Jacks, 2 x 3.5mm Jacks, 1 x 2.1 Coax 12Vdc Power Jack.
- Requires external 12Vdc power supply, Note! Not included
- Shielded Chassis Design
Calrad 92-150 IR Emitter Shield Cover
These Calrad 92-150 IR Emitter Shield Covers will reduce signal interference from local IR remote controls. The Calrad 92-150 provides IR isolation between audio video equipment that is located in close proximity to each other so discrete IR control between two similar devices are possible, like Direct TV, cable set top boxes, etc.. 3M self adhesive peel and stick design.
Calrad 92-152-NF Single Non Flashing IR Emitter, 6 ft. cord
This Calrad single Non-Flashing IR Emitter, 6 Ft. Cord, works with all (+) Tip, (-) sleeve standard Home Automation Systems and all Calrad IR Products listed below.
92-160, IR 6 Port IR Repeater-Distribution System with Gain Control:
92-180, IR 5 Port IR Repeater-Distribution System: 92-180
