Submit search
Signamax Connectivity Systems' Switching Media Converters with Link Fault Signaling (LFS) provide the means for an SNMP-Managed switch to recognize a failure on a fiber channel or twisted-pair connection, enabling the switch to automatically route to a backup path if the connected switch is equipped with Spanning Tree Algorithm.
The 72-148 provides a simple solution for providing ethernet connectivity over long distances using Cat5e/Cat6 UTP cabling. Extends any networking devices up to over 1,600 ft. at 100Mbps supports Full Duplex and Half Duplex modes. The 72-148 is completely transparent to all protocols and applications. Works with IP CCTV camera’s, VOIP Phones and all consumer based IP technologies like computers, Smart TV’s, Digital STB’s, Network Switches, Wireless Access Points, etc.. Includes two Bi-directional Transmitter and Receiver units each unit acts as a Transmitter and or Receiver. Easy to configure dip switches for connectivity options. 1 x L.E.D. Power Indicator, 2 x Mode settings L.E.D. indicators. Includes 2 x 72-148 Transmitter\Receiver units, 2 x 12Vdc power supplies.
The 72-149 provides a simple solution for providing ethernet connectivity over RG59 \ RG6u coax. Extends any networking devices up to over 1,600 ft. at 100Mbps supports Full Duplex and Half Duplex modes. The 72-149 is completely transparent to all protocols and applications. Works with IP CCTV camera’s, VOIP Phones and all consumer based IP technologies like computers, Smart TV’s, Digital STB’s, Network Switches, Wireless Access Points, etc.. Includes two Bi-directional Transmitter and Receiver units each unit acts as a Transmitter and or Receiver. Easy to configure dip switches for connectivity options. 1 x L.E.D. Power Indicator, 2 x Mode settings L.E.D. indicators. Includes 2 x 72-149 Transmitter\Receiver units, 2 x 12Vdc power supplies.
The Pan Pacific ADL-HDI-VGA+3.5 HDMI to VGA + Audio Converter is for newer laptops, computers and tablets that only output an HDMI signal. Our active device can convert from digital to analog. It's much better than most other products that only 'adapt' from HDMI to VGA. Audio is included so you can also enjoy the sound from your speakers.Micro USB power also eliminates potential power problems if users use tablets or devices that don't provide enough power for units to operate correctly.No software or driver required. Simply plug and play.PACKAGE CONTENTS:HDMI to VGA ConverterUser ManualUSB Type A to Micro USB cable (for power)FEATURES:Compliant with HDMI 1.3Support AudioSupport up to UXGA and 1080P
The Pan Pacific ADL-VGA+3.5-HDI Converter is designed to convert video (analog signal) and audio signals from a PC or Laptop to digital HDMI output up to 1080p.The VGA to HDMI Converter is a plug and play device, automatically sensing the native resolution of the display and convert the computer's output to a digital signal. The device will detect EDID displays and show the exact resolution. The converter will take the audio signal from the computer and embedded it into the HDMI signal output, so that you are able to enjoy both audio and video through one cable. It supports multiple resolutions up to 1920 x 1080 @ 60Hz.The VGA to HDMI Converter is USB powered; therefore, it will not require an additional power supply.Micro USB power also eliminates potential power problems if users use tablets or devices that don't provide enough power for units to operate correctly.No software or driver required. Simply plug and play.PACKAGE CONTENTS:VGA to HDMI ConverterUser ManualUSB Type A to Micro USB cable (for power)FEATURES:Compliant with HDMISupport AudioSupport up to UXGA and 1080P
Calrad's 40-284A is a simple solution for converting HDMI signals to VGA video & audio. It is a perfect solution for connecting video cards [desktop or laptop] or consumer electronics devices such as game consoles or home theater receivers that offer an HDMI Out port to a VGA display. The HDMI to VGA video & audio is a Plug-N-Play video converter that automatically provides instant decoding of the HDMI signals to VGA video & audio signals to facilitate the viewing of HDTV video content on televisions, projectors, RF modulators or other devices that do not have HDMI inputs. Power is supplied by the HDMI Source.
The Calrad 40-HDMI-EXT-A provides a simple method for extracting digital or analog audio from a single HDMI source at up to resolutions of 4Kx2K@60Hz. Outputs for Analog (L+R) analog, Digital optical Toslink + Coaxial audio signals. Supports (ARC) function, decodes to Toslink\Digital Coaxial outputs only. A three position slide switch and push button are provided for selecting audio functions and audio output formats. This unit supports (Non-Volatile Memory) if power is lost or removed the unit will maintain all settings.
The Pan Pacific ADL-VGA+3.5-HDI-V2 Converter is designed to convert video (analog signal) and audio signals from a PC or Laptop to digital HDMI output up to 1080p.
The VGA to HDMI Converter is a plug and play device, automatically sensing the native resolution of the display and convert the computer's output to a digital signal. The device will detect EDID displays and show the exact resolution. The converter will take the audio signal from the computer and embedded it into the HDMI signal output, so that you are able to enjoy both audio and video through one cable. It supports multiple resolutions up to 1920 x 1080 @ 60Hz.
The VGA to HDMI Converter is USB powered; therefore, it will not require an additional power supply.
Micro USB power also eliminates potential power problems if users use tablets or devices that don't provide enough power for units to operate correctly. No software or driver required. Simply plug and play.
Package Contents: VGA to HDMI Converter, User Manual, USB Type A to Micro USB cable (for power).
Stereo RCA Audio Balun Adapter over Single CAT5E/6 Cable
Stereo Analog Audio Ground Isolation Balun with IR, RS232, RS422 or RS485 Connectivity - Sold in Pairs.
This Calrad 95-1046-S1 Audio-IR-Data Pigtail Balun is ideal for residential, corporate A/V, schools, home theater applications and any other situation involving structured audio distribution that transmits stereo audio signals via Cat.5e/6 UTP cable. This Balun provides a low cost and versatile UTP cabling solution for any analog audio distribution system. Each audio channel transmission signal is completely isolated with transformer based circuitry from start to finish eliminating any issues with ground loops or audio 60hz hums. The balun also has a single 3.5mm IR signal path for bi-directional signal communication and also a cable pair for data-control communication that supports RS232, RS422, RS485. Easy bi-directional connectivity either balun can act as a transmitter or receiver. Use standard pre-made Cat5e, Cat6 cables or terminate your own cabling using the 568A standard start to finish or the 568B standard start to finish. Distances of up to 250ft., see detailed specifications below. Please Note! All 4 pairs \ 8 conductors of the RJ45 connector are used and no spare connectivity is available.
Tech Note: The RS232 Data wires can also be used for additional IR signals and low current Relay trigger connectivity
Calrad 95-1146 | Component Video Stereo Audio Extender Over Single Cat5e Cable - Sold as a Pair
Calrad’s new line of audio/ video baluns provide a simple low cost method of delivering composite video and stereo audio over UTP cable. 25k Gold plated jacks. Chassis: ABS Plastic. Extend your Component Video + L, R Audio overCat5e/6.
The Calrad 40-300 series HDMI over IP provides 1080P HD video signals over UTP network cabling. Many configurations are possible, 1.) Between a single transmitter and receiver directly without a network switch. 2.) Use multiple transmitters and receivers over an existing or separate network to create a small to large scaleable video distribution system. Up to 56 channels are possible. Using standard network switches can be used with existing networks and internet, if more than 3 transmitters are used on a 100Mb system, it is advisable to use specific 1Gb IGMP network switches to manage the signal bandwidth properly for new or existing installations. Transmitter ID addresses are easily selectable using the front panel 6 position dip switch. Receiver channel addresses are accessible by using a 12 button credit card size remote control only, to change channel addresses. Use the up down keys or direct channel address keys 0-9 to change to the desired channel. Two interface adapter cables are included for 3rd party home automation control. A full duplex bi-directional RS232 port is available for easy serial communication between devices. Easily create a virtual matrix switcher over IP with unlimited possibilities. A HDMI signal loop-output on the Transmitter is provided for continuous signal transmission to other devices.
Passive bi-directional signal design using UTP Cat5e or Cat6 cable pair. Use for Audio\Video\Component\IR signals. Cable Distance: Analog Audio, 1000 ft. Digital Audio, 300 ft. IR Signals, 300 ft. Composite video, 1000 ft., High Definition 480P - 300 ft., 720P - 200 ft., 1080I -100 ft., 1080P - 50 ft. Wire Termination: 40-DA01: 2 Conductorcaptive screw terminals Specifications: Bandwidth: DC to 50Mhz, DC passive Connectors: RCA Male Plug Signal Types: Analog+Digital Audio \ Video \ IR Signals Housing Material: Plastic, Color: Black Dimensions: 1.76"(L) x .68"(W) x .68"(H) Dimensions: L 1.32” x W 0.6” x H 0.6” 40-DA01 Male RCA Plug spacing .64 inch center to center
Extends an HDMI signal over a single CAT5e or Cat6 cable. HDCP and HDMI 3D compliant. HDMI mode, LPCM 7.1, True HD, DTS-HS or stereo audio modes. Sold as a transmitter and receiver set. 5Vdc power supplies included. Note: Only Cat 6 Cable Delivers 3D! Specifications: Video Resolution 480P, 720P, 1080P Distance: 100 Meters HDMI In\Out Connectors DC Power Supply: 5Vdc, 2A Receiver-Transmitter Size: Length 5.125" x Width 3.5" x Height 1.25"
Extend HDMI 1.3b digital signals over five 75? BNCor �F� coaxial cables. Supports 480I, 480P, 720P, 1080I and 1080P resolutions. HDMI, HDCP and RoHS compliant. Use existing coaxial cables to extend a 1080P signal up to 300 ft. Includes the HDMI over coaxial transmitter, the HDMI over coaxial receiver and 5Vdc power supply. Specifications: Video Amplifier Bandwidth:3.4 GHz Video Amplifier Frequency:340 MHz Vertical Frequency Range: 50 - 85 Hz Input Connector: HDMI Female X 1 Output Connectors: BNC Female X 5 Power Supply : 5 Vdc Dimensions: Length 4.29� X Width 2.48 x Height 1.18�
Calrad 40-1097 Wireless 1080p HDMI System This Wireless HDMI system delivers a plug-and-play method of extending HD audio/video wirelessly up to 30 meters in distance, with a perfect replication of high definition video and full digital and analog audio support for connecting HDTV sources. Featuring a performance unimpeded by line-of-sight operations, source signals are capable of transmitting through walls to accommodate multiple room installations. Wireless transmission speeds are achieved up to 300 Mbps, supporting even the most stringent demands of HD video. Built-in IR repeater system with IR receiver, IR emitter included.Specifications: * Supports up to1080P/25Hz non-compressing image and Compressed 5.1 Channel Digital Audio. * Transmission speed: 300Mbps. * Frequency: 5.18~5.32, 5.50~5.70 and 5.745~5.825GHz(ISM 5 GHz). * IR Carrier Frequency(blaster) 36k-40kHz. * Wireless: Antenna 2x3 MIMO. * Connector: HDMI 19-pin type A female. * Operating temperature: 0~50° C ambient temperature. * Storage temperature: -20~60° C. * Operation Humidity: 15%~80%(Non-condensing). * Storage Humidity: 15%~70%(Non-condensing). * Size, Transmitter, Receiver: 6.5” W x .75” H x 6” D. * Power supply: 5VDC 2A output. * IR Emitter with 5 FT. cable. * IR Receiver, with 5 FT. cable.
Upscale composite video, S-video, SVGA or component video to HDMI 1.2. Also convert digital or analog audio to HDMI 1.2 combined audio and video or digital coaxial SPIDIF output. Comprehensive OSD menu allows the user to select a variety of settings and output resolutions. IR, RS232 or manual control. Supports 480P, 720P, 1080I and 1080P resolutions. Specifications: HDMI 1.2 HDCP compliant Supports 50/60Hz frame rate conversion Picture adjustments: Contrast, Brightness, Hue, Saturation, Sharpness, RGB levels and Aspect ratio. Inputs: Component Video, Composite Video, S-Video, SVGA and HDMI 1.2+ Aux analog audio for DVI adapter connectivity. Outputs: HDMI 1.2, RCA SPDIF. Includes one ea. of a 3 ft. VGA cable, 3 ft. component cable, 3 ft. composite, L+R cable and 5 Vdc power supply.
This product is a component video (YPbPR) and stereo audio to HDMI converter that allows older analogue devices to be integrated seamlessly into the modern home theathre setup. It connects component video devices, such as Xbox 360, PS2, Wii, NTL, Virgin Media, DVD Player, Sky TV, Satellite TV, ETC. to HDMI displays. Specifications: Compliant with HDMI HIGH SPEED HDMI Resolutions: 480p, 576p, 720p, 1080i, (50HZ; 60HZ) Component Video Resoulutions: 480p, 576p, 720p, 1080i Power Supply: 5V/ 1A Input: 1 x YPbPr Input + 1 x Stereo Audio Input Output: 1 x HDMI NOTE: THIS PRODUCT CAN NOT SUPPORT HDMI 1080P!