Calrad 10-113 Microphone Splitter
The Calrad 10-113 Microphone Splitter splits input of a single microphone to two different outputs, both input and output signals may be used to provide separate isolated feeds to both a house and monitor system, P.A. recording system or similar application where double outputs are required.
Specifications:
Input Impedance: 600 ohm
Dimensions: 4 3/4" X 3 1/8" x 1 5/8"
Output impedance: 600 ohm
Frequency Response: 20-20k
Calrad 10-12 Miniature Electret Condenser Microphone
Calrad 10-12 MINIATURE ELECTRET CONDENSER MICROPHONE
This microphone is designed for all uses. ON/OFF switch enclosed on the beltclip for easy use. Designed for quality at a low cost. 6 ft. cable is terminated with a 3.5 mm plug.
Specifications:
Type: Electret Condenser
Frequency Response: 50-18Khz
Sensitivity: -65 db at 1,000Hz
Polar Pattern: Omni-Directional
Impedance: 1KOhm(=/-30% at 1 khz)
Power Supply: 1.5 volt AAA battery
Accessories: 3.5mm to 1/4" adapter, Battery, Tie Clasp, Wind Screen
Calrad 10-17 Electret Condenser Camcorder Shotgun Microphone
10-17 SHOTGUN MICROPHONE
This is a high quality sound !ocating shotgun microphone.
It is equipped with a high quality internal amplifier and earbud
type earphones. Can be easily mounted on camcorders, binoculars,
or hand-held. It has an adjustable volume control for clear output.
The supercardioid pattern is designed for medium range frequencies
to isolate and pickup human voices at directional short distances. |
|
Specifications |
Microphone
Pattern
Output Level
Acoustic Gain
Frequency Response
Power Source
Battery Life
Weight
Earphones
Measurements
Color
Accessories |
Electric condenser
Unidirectional Supercardioid
5m watts MA at earphone
50db
200-15KHZ
1 AAA Battery
100 hours (continous operation)
65 grams (incl. battery & earphones)
Inner-ear Type Stereo -32 ohms
238 (L) X 30 (H) X 17 (W)
Black
Earbud Headphones, Mounting Hardware. and Directional Tube, Thread
Adapter |
Calrad 10-22 Economy Dynamic Microphone
10-22 ECONOMY DYNAMIC MICROPHONE
This uni-directional dynamic microphone has an 10 ft. cable
and 1/4" phone plug. A wind screen is built into the wire
mesh ball head to prevent hiss, pop and wind noise.noise. |
|
Specifications |
Impedance
Frequency Response
Sensitivity |
500 ohm
80-12 kHz
-77 dB +/- 3 dB at 1 kHz |
Calrad 10-32 Collapsible Microphone Stand
10-32 MICROPHONE STAND
Polished chrome plated or black finish stem with 3/8"
- 16 thread connector and a detachable 5/8" - 27 screw adapter
for microphone holder. 2 leg base with tubular legs. Legs braced
with non-skid rubber tips. Weight: 5 Ibs. Height:collapsed -
35", extended - 64". |
Calrad 10-33 Collapsible Microphone Stand
10-33 MICROPHONE STAND
Polished chrome plated or black finish stem with 3/8"
- 16 thread connector and a detachable 5/8" - 27 screw adapter
for microphone holder. Heavy duty, compact, extra high elevation
adjustment. 3 leg base with foldable tubular legs. Boom sets
accessories included with stand for greater adjustment and versatility.
Weight: 7 Ibs., Height: collapsed - 33", extended - 63". |
Calrad 10-36-13 13" Chrome Microphone Gooseneck
5/8" - 27 connecting thread, male to
female on ends.
10-36-6................................. 6 inches
10-36-13 ............................ 13 inches
10-36-19 ............................ 19 inches
Calrad 10-36-6 6" Chrome Microphone Gooseneck
5/8" - 27 connecting thread, male to
female on ends.
10-36-6................................. 6 inches
10-36-13 ............................ 13 inches
10-36-19 ............................ 19 inches
Calrad 10-55 Metal Desk Microphone Stand
A beautiful modernistic desk stand.
"U" shaped base finished in black.
Supplied with a polished chrome
upright tube, threaded 5/8"-27 at both
ends. Can be used with the other mike
accessories.
Calrad 10-61A Microphone Holder Fits 7/8" dia. Mic.
SLIDE-IN MICROPHONE
STAND HOLDERS
Made of high impact black plastic.
Tapered design. Fits standard mike
stand 5/8 x 27.
10-61A ............... fits 7/8" dia. mics
10-63A................. fits 1" dia. mics
10-64A ............. fits 11/4" dia. mics
Calrad 10-63A Microphone Holder Fits 11/4" dia. Mic.
SLIDE-IN MICROPHONE
STAND HOLDERS
Made of high impact black plastic.
Tapered design. Fits standard mike
stand 5/8 x 27.
10-61A ............... fits 7/8" dia. mics
10-63A................. fits 1" dia. mics
10-64A ............. fits 11/4" dia. mics
