80-010 Philmore Three Digit Panel Meter/Counter Module Electronic Soldering Kit

Philmore 80-010 Three Digit Panel Meter/Counter Module Electronic Soldering Kit

This is a basic low cost counter module. Two or more may be plugged together with 6-pin sockets and harness provided. Excellent use as event counter. Uses a single 3 digit display. Uses the 14553 and 14551 chips. Has count and reset switches with debounce built in. Two or more may be joined to make 6 or 9 digit unit. display may be located remotely. Plastic case included. 9V battery operation.(not included)

Philmore Electronics part number 80-010

80-020 Philmore LCD Temperature Meter Electronic Soldering Kit

Philmore 80-020 LCD Temperature Meter Electronic Soldering Kit

Introduces 3 1/2 digit LCD and the very popular 7106 IC. This IC has been used in low-cost multimeters for over 13 years. We use it to measure temperature using a ordinary signal transistor as the sensor. Data sheets are provided as is a breadboard area so you can extend the circuit to build your own voltmeter, ammeter, resistance meter or extended-range temperature meter. Takes away the mystery of how multimeters work. Box provided. 9V battery operation.(not included)

Philmore Electronics part number 80-020

80-030 Philmore LED Dice with Slowdown Electronic Soldering Kit

Philmore 80-030 LED Dice with Slowdown Electronic Soldering Kit

A kit to introduce you to electronics and circuit analysis. Seven LEDs arranged like a real dice face. Push the switch and the dice rolls then slows down. Ingenious circuit design used to minimise components. Uses 14017 & 555. Box included. 9V battery operation.(not included)

Philmore Electronics part number 80-030

80-040 Philmore Intro to a Power Supply Electronic Soldering Kit

Philmore 80-040 Intro to a Power Supply Electronic Soldering Kit

Batteries soon become an expensive way to power your electronic kit and electronic games. This is a basic power supply in a box using two 7805 regulators. Input up to 20V AC from a transformer or power pack(not included). Two regulated outputs are available - one fixed at 5V, the other variable. Good introduction to three terminal regulators.

Philmore Electronics part number 80-040

80-050 Philmore 44 Watt Mobile Stereo Amp Electronic Soldering Kit

Philmore 80-050 44 Watt Mobile Stereo Amp Electronic Soldering Kit

The circuit is a gem. a TDA1554 IC is used to produce an amplifier that will output up to 22 watts per channel with distortion typically not in excess of 0.1% thd. Sounds quality is very very high. Consider that this kit can draw up to 5 Amps at 12VDC(not included) when supplying power.

Philmore Electronics part number 80-050

80-080 Philmore Light Alarm Electronic Soldering Kit

Philmore 80-080 Light Alarm Electronic Soldering Kit

Detects very small amounts of light and sounds the piezo alarm. Put it in your cash box or cupboard. Uses Darlington photo transistor MEL12 and 14011 IC. Educational kit.(battery not included)

Philmore Electronics part number 80-080

80-100 Philmore Touch and/or Contact Switch Electronic Soldering Kit

Philmore 80-100 Touch and/or Contact Switch Electronic Soldering Kit

Both types of switch are built onto the one PCB so you can see and explore how each type works. A battery(not included) can power the touch switch (2 contacts) but a power supply (like kit 80-040) must be used for the touch plate (1 terminal) to work. High quality 12V relay rated at switching 240V/3A supplied. Uses 14011 IC.

Philmore Electronics part number 80-100

80-103 Philmore Photo Sensor w/Control Relay Electronic Soldering Kit

Philmore 80-103 Photo Sensor w/Control Relay Electronic Soldering Kit

The most popular usage for this kit is to make your own night light. You can switch any appliance on or off with either darkness or daylight. Light sensitivity is adjustable. The relay can handle up to 10 amps. Runs on 9volt battery.(not included)

Philmore Electronics part number 80-103

80-105 Philmore Voice Changer Electronic Soldering Kit

Philmore 80-105 Voice Changer Electronic Soldering Kit

A voice is changed to add vibrato, like those used to disguise secret witnesses. Change your voice tone upward or downward or like a robot. A mic and speaker are included on the pc board. powered with a 9V battery.(not included)

Philmore Electronics part number 80-105

80-130 Philmore Sound Switch Electronic Soldering Kit

Philmore 80-130 Sound Switch Electronic Soldering Kit

Can be adjusted to turn on your tape recorder through its REMOTE plug. Has feedback and delay circuit for robust operation. Very sensitive. Proven circuit. Needs 6V plug pack for most stable operation.(not included)

Philmore Electronics part number 80-130

80-160 Philmore FM Telephone Transmitter Electronic Soldering Kit

Philmore 80-160 FM Telephone Transmitter Electronic Soldering Kit

Miniature transmitter which attaches in series with one of the two lines to your telephone. Transmits over 200 meters to an ordinary FM receiver. Transmits further if the FM receiver is near the phone line. Tune with ceramic trim cap. Uses the phone line as an aerial and power source.

Philmore Electronics part number 80-160

80-162 Philmore 6VDC Xenon Flasher Electronic Soldering Kit

Philmore 80-162 6VDC Xenon Flasher Electronic Soldering Kit

This kit builds the circuit to trigger a high voltage xenon flashtube using a 6 volt DC input from a power supply. (Transformer included) Flashrate can be varied by changing resistor &/or capacitor values.

Philmore Electronics part number 80-162

80-210 Philmore Intercom & Bug Electronic Soldering Kit

Philmore 80-210 Intercom & Bug Electronic Soldering Kit

Simple two wire intercom. Each unit with its own speaker, microphone and amplifier (LM386.) Can be modified to a hard wired 'bug'. With 4 strand ribbon cable the power can be sent to the remote 'bug' unit from the receiving unit.

Philmore Electronics part number 80-210

80-230 Philmore OP-AMP Function Generator Electronic Soldering Kit

Philmore 80-230 OP-AMP Function Generator Electronic Soldering Kit

Cheap and simple circuit to generate square, (pseudo) sine and triangle waveforms in the audio range. Uses quad opamp LM348.

Philmore Electronics part number 80-230

80-240 Philmore Logic Probe Electronic Soldering Kit

Philmore 80-240 Logic Probe Electronic Soldering Kit

This is the most important piece of equipment for testing and measuring digital equipment. It is usually used in fault finding and testing but can also assist in design work and to find out how digital equipment works. Switch for either TTL or CMOS. Our own modern design using a PUT. Includes detection circuit for very fast pulses. Gives visual (3 LEDs) and audio (piezo buzzer) response.

Philmore Electronics part number 80-240

80-260 Philmore Fiberoptic Audio Link Electronic Soldering Kit

Philmore 80-260 Fiberoptic Audio Link Electronic Soldering Kit

Allows you to send sound through plastic 1mm fibre optic cable. Matched transmitter/receiver pair from Motorola. Two circuit boards with a microphone at one end and a speaker at the other. 14 feet fibre optic cable supplied. Will work over 200 meters.

Philmore Electronics part number 80-260

80-270 Philmore 1 Watt Audio Amplifier Electronic Soldering Kit

Philmore 80-270 1 Watt Audio Amplifier Electronic Soldering Kit

A 1W power amplifier building block designed to be part of a larger project needing a low power battery operated amplifier into an 8 ohm speaker.(not included)

Philmore Electronics part number 80-270

80-280 Philmore Sound Activated FM Transmitter Electronic Soldering Kit

Philmore 80-280 Sound Activated FM Transmitter Electronic Soldering Kit

A sound activated switch and an FM transmitter joined together to make a voice activated FM transmitter. Set the level of sound that it will respond to. Two stage transmitter needs tuning to get best results. Tuning Kit and instructions enclosed. Transmits up to 1 km in the open depending on the aerial used.

Philmore Electronics part number 80-280

80-290 Philmore Combination Lock Electronic Soldering Kit

Philmore 80-290 Combination Lock Electronic Soldering Kit

An introduction to a basic but fully working combination lock. Separate touch pad with 9 pads. Lock is reset if an incorrect digit is pressed. Relay is capable of switching 240V. 12V operation. Robust and versatile.

Philmore Electronics part number 80-290

80-310 Philmore 9 Volt Siren Electronic Soldering Kit

Philmore 80-310 9 Volt Siren Electronic Soldering Kit

A surprisingly loud siren for such a simple circuit. Uses voltage controlled oscillator. 1/2 Watt, 8 ohm speaker supplied. 9V operation(battery not included). Ideal to attach to an alarm system which needs an sound module.

Philmore Electronics part number 80-310